How to Make a Homemade Battery

Author Info

Last Updated: October 3, 2023 Fact Checked

To make your own battery at home, all you need is two different types of metal, some copper wires, and a conductive material. Many household items can be used as the conductive material into which you place your metals — for example, saltwater, a lemon, or even dirt.

This battery creates electricity because the soda acts as an electrolyte for the copper strip and the aluminum strip.

Method 1

Method 1 of 4:

Making a Soda-powered Battery

Download Article

1
Gather your materials. For this battery, you will need one unopened can of soda (any type will do), one plastic cup (6 to 8 ounces), and one 3/4-inch-wide strip of copper that's slightly longer than the height of the cup. In addition, you'll need a pair of scissors, a voltage meter, and two electrical lead wires with alligator clips at both ends.^{[1]
X
Research source}
- If you don't already have these materials around your house, you can purchase them at a hardware store nearby.
- You can substitute the copper strip with several pieces of copper wire stuck together or bent in a zig-zag fashion to reach the desired width.
Note that the cup doesn't absolutely have to be plastic.^{[2]
X
Research source} It just has to be non-metallic. Styrofoam and paper cups will also work if you don't have that.

Advertisement
Discard (or drink) any soda that remains in the can. Turn it upside down in the sink and give it a few extra shakes to make sure that all the soda is out.
4
Cut a strip of aluminum from the soda can. Cut a 3/4-inch-wide strip from the side of the soda can. Ensure that's it's slightly longer than the plastic cup's height; if this isn't possible, don't worry — you can just bend the top of the strip and let it hang over the edge of the cup and into the fluid.
- Instead of cutting the can, you may purchase aluminum strips from a hardware store.
- Aluminum foil is not an effective replacement for an aluminum strip; don't use it!
You can skip this step if you bought the aluminum from a hardware store. If you cut the strip from a soda can, you'll need to sand off the coatings (i.e. paint, plastic) on both sides of the strip.
6
Place the strips into the solution. Ensure that the strips do not touch each other. Place them across from each other — not side by side or overlapping — in the cup.
- Ideally you've cut the strips long enough that their tops sit above the soda, extending slightly past the rim of the cup.
- If the strips do not extend past the cup's rim, you can bend each strip lightly so that it hangs off the edge of the cup.
7
Attach lead wires to metal strips. Attach one lead wire to one metal strip by opening the alligator clip and closing it on the strip. Then, attach a different lead wire to the other metal strip, again using the alligator clip.
- Be careful not to let the alligator clips touch the soda.
- It doesn't matter which color of wire attaches to which strip.
Following the instructions that come with your voltage meter, connect a lead wire from each metal strip to the voltage meter. The meter should read your battery's voltage at roughly 3/4 of a volt.

Method 2

Method 2 of 4:

Making a Saltwater-powered Battery

Download Article

1
Gather your materials. For this battery, you'll need one plastic cup (6 to 8 ounces), two 3/4-inch-wide strips of metal that are taller than the cup, and one tablespoon (14.79 ml) of salt. Each strip must be a different type of metal, but you can choose which type: zinc, aluminum, and copper are popular choices. In addition, you'll need a pair of scissors, a voltage meter, and 2 electrical lead wires with alligator clips at both ends.
- A variation on this recipe is to add one teaspoon (4.93 ml) of salt, one teaspoon (4.93 ml) of vinegar, and a few drops of bleach to the water instead of one tablespoon (14.79 ml) of salt. If you choose this variation, be careful, as bleach is a hazardous chemical.
- Metal strips, electrical lead wires, and voltage meters are available at hardware stores. You should also be able to find lead wires at shops that sell electrical components.
Note that the cup doesn't absolutely have to be plastic. It just has to be non-metallic. Styrofoam and paper cups will also work.
It's the same process if you decide to follow the salt, vinegar, and bleach variation.
Ensure that the strips are touching the saltwater and extending past the cup's rim.^{[3]
X
Research source} If the strips are too short, bend them so that they hang off the cup's rim and dip into the solution.
5
Attach the lead wires to the metal strips. Attach one lead wire to one metal strip using an alligator clip. Then, attach a different lead wire to the other metal strip, again using the alligator clip.
- Be careful not to let the alligator clips touch the water.
- It doesn't matter which color attaches to which strip.
Following the instructions that come with your voltage meter, connect a lead wire from each metal strip to the voltage meter.^{[4]
X
Research source} The meter should read your battery's voltage at roughly 3/4 of a volt.

Method 3

Method 3 of 4:

Making 14-cell Water-powered Battery

Download Article

1
Gather your materials. For this battery, you'll need some copper wire, 15 sheet metal screws, an ice cube tray, and water.^{[5]
X
Research source} In addition, you'll need a pair of scissors, a voltage meter, and two electrical lead wires with alligator clips at both ends. You'll wrap each screw in copper except for one, which you will use as a negative terminal (to which you will attach one of the lead wires once the battery is complete).
- How many screws you use will depend on how many ice cubes your tray is meant to hold. The tray in this example can hold 14 ice cubes.
- As long as they aren't copper, you can use any type of metal screw. Zinc-coated (galvanized) or aluminum work well.^{[6]
  X
  Research source} As for size, aim for screws that are around one inch in length.
2
Wrap copper wire around 14 of the 15 screws. Wrap a piece of copper wire two times around the top of each screw, just beneath its head. After wrapping the wire around a screw, use your finger to bend the wire into a hook. You'll use this hook to clip the screw to the edge of its ice cube tray compartment.
- You can either pre-cut the copper wire into pieces long enough to wrap around each screw (with a bit extra for the hooks), or you can work with it long, cutting it as you finish each screw.
Each ice cube hole will act as a single cell in your battery. Affix one screw to the edge of each cell. Ensure that there is only one screw in each cell.
On one end of the tray, hook a piece of copper wire to the outer edge of one of the cells. On the same end of the tray, place a screw in the cell next to the one in which you just placed the copper wire. Ensure that the screw sits above the rim of the tray, as you will need to attach a lead wire to it.
Ensure that the cells are full enough that the copper wire hooks and screws are touching the water.
6
Attach lead wires to positive and negative terminals. Attach one lead wire to the copper wire terminal using its alligator clip. Then, attach a different lead wire to the screw terminal, again using its alligator clip.
- Be careful not to let the alligator clips touch the water.
- It doesn't matter which color attaches to which terminal.
Attach the other ends of the lead wires to your voltage meter. The 14-cell battery that you've just made should measure roughly 9 volts.
You can boost the voltage of your battery by switching your conductive solution to saltwater, vinegar, bleach, lemon juice, or lime juice, or by using more copper.^{[7]
X
Research source}

Method 4

Method 4 of 4:

Making a Hand-powered Battery

Download Article

1
Gather your materials. For this battery, you'll need one copper plate and one aluminum plate -- both roughly the size of your hands. You'll also need two electrical lead wires with alligator clips at both ends, and you'll need a voltage meter.
- You can purchase the metal plates, wires, and voltage meter at a hardware store.
If you don't have a piece of wood, you can also place the plates on another non-metallic surface — for example, plastic.
3
Connect the plates to a voltage meter. Using the alligator clips, connect the copper sheet to one end of the voltage meter, and the aluminum sheet to the other end of the voltage meter.
- If you're unsure of how to connect items to your specific voltage meter, check its instruction manual.
4
Place one hand on each plate. When you place your hands on the metal plates, the sweat on your hands should react with the metal plates to produce a reading on the voltage meter.
- If the meter doesn't show a reading, reverse your connections: attach the copper plate to the terminal that the aluminum plate was connected to, and vice versa.
- If you still struggle to get a reading, check the connection and wiring. If everything is working well, it could be that the plates are oxidized. To remove oxidization, clean the plates with a pencil eraser or steel wool.

Community Q&A

Search

Add New Question

Question

What in the Coke is attracted to the copper and aluminum?

Community Answer

The Coke contains phosphoric acid, which acts as an electrolyte. The electrolyte act as a barrier to the electrons, forcing them to go through one wire, through the device, thorough the other wire and back to the opposite end of the battery, all in an attempt to create a state of equilibrium with the negative and positive charges.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 52 Helpful 152
Question

For the experiments, why use soda, lemon juice, or vinegar?

Community Answer

They make the voltage higher. When the liquid's pH is farther away from neutral (7), they make more electricity.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 31 Helpful 90
Question

What is the science behind a salt water battery?

Community Answer

One of the main components of a battery is an electrolyte. Electrolytes can be found in sodium ions, which compose salt.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 40 Helpful 92

See more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

For the aluminum + copper + fluid batteries, you should be able to get a long use out of them (some people suggest several years), but you'll need to renew the fluid and lightly sand the copper strips every three months (or sooner, if they are very corroded).^{[8]
X
Research source}

Thanks
Helpful 2 Not Helpful 0
To make a soda-powered or a saltwater-powered battery stronger, fill multiple plastic cups with the metal strips/fluid solution. Next, connect the metal strips on each cup with the opposite type of strip on the cup next to it using clip leads — for example, a copper strip should be connected to an aluminum strip.

Thanks
Helpful 28 Not Helpful 7
Using three or more saltwater or soda batteries should be enough to power a simple device such as an LCD clock.

Thanks
Helpful 31 Not Helpful 10