ControlLogix High Speed Counter Module

Electrical

Suitable for safety functions	No
Digital inputs configurable	Yes
Digital outputs configurable	No
Voltage type of supply voltage	DC
Type of electric connection	Screw connection
Total backplane power	1.6 W
Thermal dissipation	19.1 BTU/h
Number of counters	2 counters
Current draw	300 mA @ 5.1V, 3 mA @ 24V
Module keying	Electronic, software configurable
Outputs	4 (2 points/group)
Power dissipation, max	5.6 W @ 60 °C(140 °F)
Isolation voltage	125V (continuous), basic insulation type, input group-to-backplane, 30V (continuous), basic insulation type, input group-to-input group
Wire category	2 on signal ports, 1 on power ports
Short-circuit protection, outputs available	No
Inputs per counter	3 (A, B, Z for gate/reset)

Mechanical

Slot width	1
RTB keying	User-defined mechanical
Shock	Operating: 30 G, Non operating: 50 G
Vibration	2 G @ 10...500 Hz

Environmental

Surrounding air temperature, max	60 °C
North American temperature code	T4
Emissions	IEC 61000-6-4
ESD immunity	6 kV contact discharges, 8 kV air discharges
Relative humidity	5...95% noncondensing
Conducted RF immunity	10V rms with 1 kHz sine wave 80% AM from 150 kHz...80 MHz on shielded signal ports
EFT/B immunity	±4 kV @ 5 kHz on power ports, ±4 kV @ 5 kHz on signal ports
Operating temperature	0 to 60 °C
Surge transient immunity	±1 kV line-line (DM) and ±2 kV line-earth (CM) on power ports, ±1 kV line-line (DM) and ±2 kV line-earth (CM) on signal ports, ±2 kV line-earth (CM) on shielded ports
Radiated RF immunity	10 V/m with 1 kHz sine-wave 80% AM from 80...2000 MHz, 10 V/m with 200 Hz 50% Pulse 100% AM @ 900 MHz, 10 V/m with 200 Hz 50% Pulse 100% AM @ 1890 MHz, 3 V/m with 1 kHz sine-wave 80% AM from 2000...2700 MHz
Nonoperating temperature	-40 °C

Input Specifications

Counting frequency, max	1000 kHz
Count range	0...16, 777, 214
Operating voltage	5V operation: 4.5...5.5V DC, 12/24V operation: 10...26.4V DC
Input frequency, max	1 MHz in counter modes (A input), 500 kHz in rate measurement mode (A input), 250 kHz in encoder mode (A/B inputs, X1 or X4), 70 Hz with filter enabled
Input current, min	4 mA
Input current, nom	15 mA

Output Specifications

On-state voltage drop, max	0.55 V
Off-state leakage current per point, max	300 μA
Load current per point, min	5V operation: 3 mA, 12/24V operation: 40 mA
Short circuit protection	Electronic (remove overload and toggle On/Off to restore.)
Reverse polarity protection	Yes (if wired incorrectly, module outputs can be permanently disabled.)
Output control	Up to two outputs are assigned to each counter channel, each output can have two ‘turn-on’ and ’turn-off’ preset values
Output delay time	OFF to ON: 20 µs nominal, 50 µs maximum, ON to OFF: 60 µs nominal, 300 µs maximum
Counter, max	1 MHz
Debounce filter, max	70 Hz
Rate measurement, max	500 kHz
Encoder, max	250 kHz
Current limit	<4 A
Surge current per point	2 A for 10 ms every 1 s @ 60 °C (140 °F)
Output current rating, per point	20 mA @ 4.5...5.5V DC, 1.0 A @ 10...31.2V DC

Certification

IEC temperature code	T4

Construction

Enclosure type	None (open-style)