Hopkins 7-Way RV Style Connector with Molded Cable - Trailer End - 8' Long - RV Standard

Ask the Experts about this Hopkins Wiring

• Will 7-Way Connector Charge Auxiliary Trailer Battery
  The yellow wire on the Hopkins 7-Way RV Style Connector with Molded Cable # H20046 will not be able to charge an on-board battery, it should really be used for reverse lights. To charge the auxiliary battery on your trailer the best option is to use a battery charger such as the CTEK MULTI US 3300 12-Volt Universal Battery Charger # CTEK56353 which you would plug into a standard outlet. You can maintain that charge when driving by running # 10-1-1 wire along with 40 amp circuit breaker...
  view full answer...
• Adding 5-Way Harness to 2018 Toyota Highlander With 4-Flat
  I'm a bit confused by your question; the Highlander you are getting has just a 4-pin flat, is that correct? And you are looking to tow a trailer with a 5-flat?
  view full answer...
• Gauge Wire to Use When Wiring Up Brake Assemblies
  10 gauge wire like our part # 10-1-1 (sold by foot) is the correct gauge to use for trailer brake output circuits as it can deliver the amperage needed to activate the brakes properly.
  view full answer...
• What Gauge Wire Should be Used to Wire Trailer Brakes
  That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary. On a smaller trailer with a single axle of brakes 12 gauge wire would probably be enough. But for a longer tandem axle trailer I would recommend you run 10 gauge wire to all the assemblies just to minimize the amount of resistance that would be on...
  view full answer...
• Can Electric Drum Brakes be Added to a Utility Trailer
  It can be possible to add electric drum brakes to an existing trailer that does not have them. The linked article explains in detail. The trailer will need to have or be fitted with brake flanges, the brake assemblies and hub/drums of matching dimensions and trailer wiring to support the brake circuit. The tow vehicle will have to be equipped with a trailer brake controller and a suitable trailer socket to match the one on the trailer. Typically trailers with brakes use a 7-way RV-style...
  view full answer...
• Is Replacement Trailer Side 7-Way Connector # H20046 Male or Female
  The Hopkins 7-Way connector, part # H20046, is a male connector. The trailer side is the male end because it inserts into the vehicle side. This is somewhat misleading because usually a male connector has prongs and vehicle side trailer connectors have the prongs even though it is a female connector. I've never seen a vehicle with a male trailer connector. Likewise with a female on a trailer. Take a look at the pictures I've attached and see if they match the type of setup you have....
  view full answer...
• Replacement 7-Way and Junction Box for 5th Wheel Trailer with Non-Functioning Brakes
  Since you have confirmed that your 5th wheel's brakes do not work even when connected to a different tow vehicle you will want to focus on the trailer for your troubleshooting. There are simple troubleshooting steps you can take to isolate the problem on the trailer. First, I suggest checking the condition of the 7-way plug. Sometimes corrosion can develop INSIDE the plug housing where it is all but impossible to detect. Normal exposure to the elements can cause this. Since your brake...
  view full answer...
• Recommendations For Re-Wiring Horse Trailer With Brakes
  Since you said you have a 7-way blade connector on your Silverado I would start with the 7-Way Molded Trailer Wire Connector, part # H20046. This is an 8 ft long harness with the 7-way trailer connector. If you need a shorter harness you can check out part # H20044 which is a 6 ft long harness with the connector. You will want a circuit tester like part # 40376 to make sure you match the wiring on the trailer side connector to the functions on the vehicle connector. I then recommend...
  view full answer...
• Wiring Trailer Reverse Lights Using Spectro Trailer Wiring Junction Box # 38656
  Power for your trailer's backup lights needs to come from the tow vehicle's reverse light circuit. You will need to choose one of the available circuit posts on the Spectro Junction Box # 38656 as the one you'll use for the reverse light circuit. Usually this would be the Auxiliary post at the far end of the box opposite the ground. Please refer to the linked photo. It does not matter what color wire you use to wire the trailer (although using the conventional colors does help keep...
  view full answer...
• Equipping 2004 GMC Sierra to Maintain Battery on Enclosed Trailer
  What you are wanting to do is actually pretty simple. The 12-Volt accessory circuit on your 7-way can be used to tend or maintain your battery on your trailer, but the circuit does not have sufficient amperage to charge a battery that has been completely discharged. Using a battery isolating solenoid like part # TR118665 would be advisable. This will prevent the battery on the tow vehicle from being discharged by disabling the 12-volt accessory circuit from the 7-way once the ignition...
  view full answer...
• Can 7-Way Molded Trailer Wire Connector Connect to Roadmaster 6-Way # RM-910030-6
  Yes, the terminals of the RoadMaster 6-Way connector and socket part # RM-910030-6 are compatible with 10 gauge wire like what comes with the # H20046. The center pin of the 6-way is the 12 volt accessory circuit and the ground is the circuit in the 2:00 position as you look into the opening of the connector.
  view full answer...
• How To Hardwire a New 7-Way Trailer Connector by Function When Wire Colors Do Not Match
  You will need to wire the 7-Way Molded Trailer Wire Connector, # H20046, for function rather than by color. Since the trailer side needs to be replaced, you will need to trace the wires back to see which wire does which function. An easier option would be to test the connector you have, before replacing it, to see which wire color matches which function on the trailer side of the connector. Using a circuit tester, like # PTW2993, test the trailer side wires for: right turn and stop,...
  view full answer...
• How to Make 6-Way Square to 7-Way Adapter
  To make a 7-way to 6-way square adapter will require you to get the part # 37995 to use the 6-way end and then wire up a 7-way to it like part # H20043. This will give you the adapter you would need since there isn't one already pre-made.
  view full answer...
• Troubleshooting Tekonsha P3 Brake Controller 90195 Overload Issue
  Since your local technician tested your Pathfinder's 7-way and found it to have a functional trailer brake circuit, AND since your new trailer behaved properly when connected to another tow vehicle, the issue I suspect you might have is an intermittent short in the trailer wiring. If the trailer is not brand new there could be corrosive build-up on or even inside the 7-way plug. Water can over time migrate into even a sealed/molded 7-way plug like # H20046 and cause adjacent circuits...
  view full answer...
• Does 7-Way Molded Trailer Wire Connector Have a Reverse Light Function
  Yes, the center pin on trailer side wiring harness # H20046 is for reverse lights on the trailer. For this particular harness it is the yellow wire. But it will only work if the center pin is functional on your 2012 Toyota Tacoma. If you have the factory installed 7-Way on the Tacoma then it should be active.
  view full answer...
• Are All 7 Way Blade Connectors the Same
  Yes, there is only one type of 7-way blade connector. I am attaching a help article about wiring that may be of interest to you.
  view full answer...
• Installing Hopkins 7-Way Trailer Pigtail to 2001 Sundowner Trailer
  The Hopkins 7-Way RV Style Connector with Molded Cable - Trailer End - 8' Long - RV Standard # H20046 will connect to your 6 wires function for function. Many trailers will not have the reverse light function, so it is likely that you have a ground yet it is simply a different color wire on your trailer. If you check the functions using a circuit tester like # PTW2993 it is likely the red (auxiliary/backup) wire will not be used on this harness and the blue wire will only have function...
  view full answer...
• How To Wire In a 7-way to Replace a Boat Trailer 5-Way Flat
  You definitely could install the 7-Way Molded Trailer Wire Connector # H20046 in place of the 5-way that is installed on your trailer currently. The colors wouldn't match up exactly. White would go to white, you would run both brown wires to the single green wire of the 7-way. Yellow of your trailer would go to the red wire of the 7-way, and green of the trailer wiring would go to brown of the 7-way. Now without knowing where the red wires of the 5-way go it's hard to say for certain....
  view full answer...
• 7-Way Diagram for 7-Way of 2014 Mercedes Sprinter 3500
  The PA66-MD40 is a standard 7-way which we have diagrams for. I attached a picture that shows how a standard RV 7-way gets wired up for you to check out.
  view full answer...
• Diagnosing Malfunctioning Turn Signal and Brake Lights on Gooseneck Trailer
  Although the brake and turn signals work on the truck, I would recommend testing the 7-way connector on the truck to determine if the problem exists in the trailer wiring on the vehicle, or on the trailer. Use a circuit tester like part # 40376 and test the pins on your 7-way that are in the 3:00 and 9:00 position. With the right turn signal on you should see power on the pin on the 3:00 location. With the left turn signal activated, the pin in the 9:00 location should light up the tester....
  view full answer...
• How is Length of 7-Way Connector Lead Determined for Wiring Up Trailer
  The method you described would be a great way to determine what length to cut the # H20046. That way you would end up with enough wire that it wouldn't come unplugged when making a tight turn. Securing the wire up and out of the way is a smart option as well so that the weight of the cable would not want to pull it out of the connector and so that it doesn't get caught on anything.
  view full answer...
• 7-Way Trailer Connector has 8 Wires and Brake Lights do not Work
  On a 7-Way trailer connector the brake lights and turn signals are on the same circuits. The pins in the connector at the 3 o'clock and 9 o'clock positions are the turn signal and brake light circuits. On the tow vehicle side use a circuit tester such as # 40376 or a meter if you have one to test those pins while someone sits in the vehicle and steps on the brake pedal. If there is no power on those pins during this test then the issue is on the vehicle side and is likely a blown or missing...
  view full answer...
• Is a Battery Isolator Needed when Adding a Battery to a Trailer
  First, the 12 volt circuit from a trailer connector, and most factory alternators on vehicles, are not able to charge up a trailer mounted battery. What they will do is provide a maintenance charge and keep the trailer battery at its current charge level. A battery isolator will only send power back when the vehicle is running. This will help to keep from draining the vehicle battery. Or you could just disconnect the trailer from the tow vehicle when you stop for long periods of time....
  view full answer...
• Adding a Battery and Wiring to a Non-Powered Trailer to Add Interior Lights to an Enclosed Trailer
  The first thing you will need is a battery and a battery box. The wiring for the light will need to be connected directly to this battery via a switch that you can get at a hardware store if the light does not already have a switch. Or you can install a new light that has a switch like the Trailer Dome Light with Switch and Aluminum Base, # IL61CB. Mount the switch in the trailer, route the wiring from the light to the switch, and then from the switch to the battery. If the light is...
  view full answer...
• Troubleshooting Trailer Lights Not Functioning When Headlights are On
  It sounds like you have a bad ground connection. If all ground connections are not making good contact to bare metal, when the tail lights are turned on then the trailer lights will go out or not function properly. You will need to check all of the ground connections especially where the tail lights are mounted to the trailer frame, and where the light brackets are mounted if they are bolted to the frame. If a plastic license plate holder is mounted between the left side taillight and...
  view full answer...
• Wire Colors and Functions of Hopkins 7-Way Molded Trailer Wire Connector
  There are two color code standards that are used in the trailer world. The Hopkins 7-Way RV style connector and cable, # H20046, that you referenced uses the RV Industry standard color code which is as follows: White Wire - Ground Red Wire - Left Turn/Brake Brown Wire - Right Turn/Brake Green Wire - Tail Lights Blue Wire - Brake Controller Output Black Wire - 12 Volt hot lead Yellow Wire - Reverse Lights or Auxiliary Circuit This color code is commonly found on camping trailers...
  view full answer...
• Recommendations For Complete Re-Wiring Of 6 X 12 Enclosed Trailer With LED Lights
  We do have everything you need to re-wire your 6 X 12 enclosed trailer. We also have any of the lights you said you want to use as well. For trailer wiring I recommend installing a 7-way so you can operate the light inside the trailer. The 7-way wiring I recommend is the Hopkins # H20046. This harness is an 8-ft long molded 7-way. I then recommend using a junction box like part # 38656. You would mount this on your trailer and then run your # H20046 wiring into the box. You can...
  view full answer...