Working on my coleman 2C stove. Noticed that the generator has some scoring from rubbing on the steel guide as it goes from hot blast position to run position. Any thoughts?
There is no leak now but....
Could I put a bit of solder there so that the rubbing is on the solder....and just replace the solder every 100 yrs ?
Maybe a collar of copper or very thin steel held in place by the clamp next to the worn spot?
Also.. Had to use a little Harvey's yellow pipe goo to stop a stubborn leak. What can I use to clean up the extra?
thanking all you kind and knowledgeable folk in advance!
coleman 2C stove scoring of generator
-
- Senior Member
- Posts: 199
- Joined: Wed Sep 28, 2016 1:50 am
coleman 2C stove scoring of generator
"May the Blessings you receive each day be the Blessings you need most"..Traditional Irish Blessing
-
- Senior Member
- Posts: 199
- Joined: Wed Sep 28, 2016 1:50 am
coleman 2C stove scoring of generator
Bumping this... hoping someone has some thoughts on this. thank you
"May the Blessings you receive each day be the Blessings you need most"..Traditional Irish Blessing
-
- Moderator
- Posts: 8831
- Joined: Wed Aug 21, 2013 2:37 am
coleman 2C stove scoring of generator
Yes, find a piece of copper pipe slightly larger than your gen tube. You might use some thinner LP gas copper line not full blown water/plumbing pipe.
Cut it long enough to cover the area in question. Then, probably using a Dremel and cutting wheel, slit the pipe down the length of it and slip it over the gen. Put it in place and as you tighten the clamp it should compress the pipe holding it secure.
Cut it long enough to cover the area in question. Then, probably using a Dremel and cutting wheel, slit the pipe down the length of it and slip it over the gen. Put it in place and as you tighten the clamp it should compress the pipe holding it secure.
Chuck
"...follow all that I commanded you; and behold, I am with you always, to the end of the age.” Matthew 28:20
Eye-SEE-C-C Member #1333 -- MilSpecOps #003
"Michigan - from the Ojibwa word “meicigama,” meaning “great water.”
"...follow all that I commanded you; and behold, I am with you always, to the end of the age.” Matthew 28:20
Eye-SEE-C-C Member #1333 -- MilSpecOps #003
"Michigan - from the Ojibwa word “meicigama,” meaning “great water.”
-
- Senior Member
- Posts: 199
- Joined: Wed Sep 28, 2016 1:50 am
coleman 2C stove scoring of generator
Thank you!
"May the Blessings you receive each day be the Blessings you need most"..Traditional Irish Blessing
-
- Moderator
- Posts: 8831
- Joined: Wed Aug 21, 2013 2:37 am
coleman 2C stove scoring of generator
BTW, sometimes you can find copper line pretty cheap in kits for refrigerator ice makers. Not sure about all the diameter's they offer with those though.
I think our True Value Hardware store sells that copper line, cut to the length you need. I'd get at least a foot since other small projects can come up from time to time.
I think our True Value Hardware store sells that copper line, cut to the length you need. I'd get at least a foot since other small projects can come up from time to time.
Chuck
"...follow all that I commanded you; and behold, I am with you always, to the end of the age.” Matthew 28:20
Eye-SEE-C-C Member #1333 -- MilSpecOps #003
"Michigan - from the Ojibwa word “meicigama,” meaning “great water.”
"...follow all that I commanded you; and behold, I am with you always, to the end of the age.” Matthew 28:20
Eye-SEE-C-C Member #1333 -- MilSpecOps #003
"Michigan - from the Ojibwa word “meicigama,” meaning “great water.”
-
- Super Colemanaholic
- Posts: 3578
- Joined: Mon Sep 28, 2015 11:17 pm
coleman 2C stove scoring of generator
If you have a hobby store (airplane type) available, you might get a piece of brass tubing and make a curved patch from that. Craft stores have rolls of thin brass sheet that might also be used for patch material. I'd just go with a bit of solder to make a wear surface.
-
- Senior Member
- Posts: 199
- Joined: Wed Sep 28, 2016 1:50 am
coleman 2C stove scoring of generator
many thanks to all. Looks like a little copper or brass shield is the way to go to protect this old generator.
"May the Blessings you receive each day be the Blessings you need most"..Traditional Irish Blessing
-
- Certified Colemanaholic
- Posts: 13338
- Joined: Sun Mar 06, 2016 8:10 pm
coleman 2C stove scoring of generator
Or, not worry and realize that it will take more than your remaining lifetime to wear through.
It's priceless until someone puts a price on it.
Walk a mile in a man's shoes before you criticize him--then you're a mile away, and he has no shoes.
Texan's last words: "Y'all--hold my beer--I wanta' try sumptin'."
Timm--Middle of nowhere, near the end of the road, Oregon.
Walk a mile in a man's shoes before you criticize him--then you're a mile away, and he has no shoes.
Texan's last words: "Y'all--hold my beer--I wanta' try sumptin'."
Timm--Middle of nowhere, near the end of the road, Oregon.
-
- Certified Colemanaholic
- Posts: 11944
- Joined: Thu Dec 11, 2008 11:12 pm
coleman 2C stove scoring of generator
i wonder if the genny isnt seated all the way , like the clamp should just be on the round section and not the hex portion . just an observation . i have a 2C ill have to take a look at and refresh my memory
Steve , Keeper of the Light !!!
-
- Senior Member
- Posts: 199
- Joined: Wed Sep 28, 2016 1:50 am
coleman 2C stove scoring of generator
Thank you, Steve. Good thought
"May the Blessings you receive each day be the Blessings you need most"..Traditional Irish Blessing