The 1960s were an incredible time to be alive, especially for car lovers with a need for speed. It was then that the muscle car wars started, with Mopar (Dodge, Plymouth, and Chrysler) and Ford battling it out for drag racing supremacy. All that ended after the early- ‘70s, when the oil crisis and federal regulations slowed the automaker’s roll.
From the smell of the exhaust to the feeling of a rumbling, carbureted V-8 engine infiltrating your bones, there is nothing like the feeling of freedom while driving a muscle car in the 1960s. Thankfully, the classic car automotive market is still lively, allowing us to offer the next best thing to the old school muscle car experience. Check out five of our favorite muscle car auctions, ending soon on the Hemmings.com Marketplace.
Supercharged 1971 Dodge Demon
This classic Dodge Demon street machine isn’t afraid to flex its muscles. The prominent Roots-style supercharger bursting through the hood sits on top of a 440-cid V8. Dyno tuning has clocked the Demon at an estimated 1,000 horsepower at the flywheel, according to the seller. The four-speed transmission sends 740 horsepower to the rear wheels.
The supercharged powertrain isn’t the only update; the car also received a rotisserie-type restoration to straighten the body and unitized chassis before being sprayed with a fresh coat of Glacier Blue paint. According to the auction listing, the Demon also sports four-wheel disc brakes, custom-trimmed interior, and a “killer” stereo system, plus more. Since the restoration, the Demon reportedly has appeared in magazines and has earned several show awards.
V8-Powered 1971 Plymouth Scamp
The 1971 Plymouth Scamp, essentially a Dodge Dart with a Plymouth Duster (or Valiant) front end, offered power from an indestructible 225-cid. Slant-Six or Chrysler’s workhorse, the 318-cid. V8. According to the seller, this example was updated with a larger-displacement 360-cid. V8 manufactured in 1974, paired with an automatic transmission.
It also has power front disc brakes and clean interior, and the seller states there’s "no known rust." The photos support that statement and also show a four-barrel carburetor mounted on an aluminum intake manifold, along with an electric fan mounted on an aluminum radiator. Find out more about this sporty Lime Green Scamp by following this link to the Hemmings auction listing.
Numbers-Matching 1969 Pontiac GTO
Some automotive historians have stated that the first true muscle car to roll off of factory lines was General Motors’ Pontiac GTO. Whether or not you agree, this example of pure muscle is hard to beat.
According to the seller, “This beautiful second-generation 1969 Pontiac GTO is powered by its matching-numbers 400-cu.in. V8 and was optioned with a four-speed standard transmission with Hurst shifter.” The GTO’s engine was factory rated at 350-horsepower, and 445-lb-ft of torque with a four-barrel carburetor.
This car was also factory equipped with additional desirable extra-cost items, such as the M20 four-speed manual transmission, retractable headlamp covers, A/C, and a hood tach, as well as power steering. The Judge spoiler stripes and decals were added by a previous owner, as were the open hood scoops and Ram Air system, and power front disc brakes. The listing states that an electronic ignition has been added, and the carburetor has been swapped, but the original Quadrajet is included in the sale.
Numbers-Matching 1970 Chevrolet Chevelle SS 396
The eye-catching color combination of this 1970 Chevrolet Chevelle SS 396 combination was selected for many of the original brochures and print ads, giving it an extra nostalgic pull. According to the seller, the numbers-matching muscle car has had four owners. It was reportedly stored from 1987 to 2007 and underwent a body-off restoration that began in 2007 with a 2010 completion.
The seller states the Chevelle “retains its matching-numbers 402-cu.in., four-barrel, OHV V8, M40 Turbo Hydra-Matic 400 transmission, and 12-Bolt Positraction rear axle, as well as its original body panels.”
“This car is spotless,” he added, and the photos show exactly that. Click here to cruise to the auction listing.
Restored 1967 Mercury Cougar
After its debut in 1967, the Mercury Cougar was awarded the "Car of the Year" by Motor Trend magazine, a signature automotive industry award. Car Life was also impressed with the newly released 1967 Mercury Cougar, calling it a “finished product… done with subtle discernment.” Testers lucky enough to drive it praised the Cougar for having an identity of its own, offering more refinement than its corporate sibling, the Mustang.
This 1967 Mercury Cougar hardtop was reportedly restored to AACA show standards, and the 61,655 miles showing on the odometer are believed to be original. According to the listing, the fifth digit of the VIN, “C,” designates the engine as a 200-horsepower, two-barrel carburetor, 289-cu.in. OHV V8 that the seller says was represented to him as “a numbers-matching engine.”
A photo showing the breakdown of the VIN and trim tag is located in the Tag photo gallery of the auction listing.
- A guide to the best '80s and '90s muscle cars, and why they're still ... ›
- SEMA 2023 Gallery: Muscle Cars from the Show Floor | Hemmings ›
- Over 300 Classic Muscle Cars Unveiled in Texas Barn Find ... ›
- A Look Inside a Private Stash of Rare Muscle Cars | Hemmings ›
- Better Than a Barn Find: Floor-to-Ceiling Mopar Muscle Cars and ... ›
- Muscle Cars for Sale | Hemmings ›
The piston top plays a vital role in determining compression on any engine. Dished pistons will add to the combustion chamber volume while domed pistons are intended to reduce overall volume and increase compression. The ideal combustion space combination is a flat piston top with a small chamber to improve combustion efficiency.Photo: Courtesy of Mahle Motorsports
Before we get into specifics, let’s first discuss how compression ratio is determined. In the old days before computers, engine builders had to run through the laborious task of determining the volume of each of the above variables. Bore and stroke for the cylinder is easy using the basic geometry of the volume of a cylinder which is the area of a circle (the bore) times the depth or length of the cylinder. The formula is from high school geometry: Pi x radius x radius x length. This is also the same formula you would use to calculate the volume of the piston above or below the deck as well as head gasket volume based on bore size and the thickness of the gasket.
The formula to compute the volume of the cylinder at the top of the stroke includes the piston top configuration (dish or dome), chamber size, head gasket thickness, and the distance the piston was either above or below the deck surface of the block. With regard to piston position, a piston that stopped its travel below the deck effectively adds this volume to the chamber size while a piston that travels above the deck would reduce that volume from the chamber.
Even simple valve reliefs can affect compression. This standard four-eyebrow small-block Chevy replacement piston measures nearly 7cc’s worth of volume. Compare that to a pure flat-top, 6.0-liter Mahle piston with no reliefs. Of course, ensuring proper piston-to-valve clearance is important with either piston but the balance is always a compromise between adding compression yet avoiding bending valves when they hit the piston. Photo: Courtesy of Mahle Motorsports
We won’t get into the long-hand version of calculating compression only because it is both tedious and unnecessary now with the advent of online compression ratio computer programs. But it is important to understand the relationships between the components so that you can make decisions more effectively.
To assist in this process, you may need to convert combustion chamber volume that is usually measured in cubic centimeters (cc’s) into cubic inches or the opposite of cubic inches into cubic centimeters. We’ve listed these conversions in a separate chart to make finding them easy. As an example, a 70cc chamber converted to cubic inches would be 4.27 cubic inches.
As mentioned in the story, crankshaft bore and stroke are significant contributors to compression or the lack of it. It is much easier to create compression with a longer stroke engine than one with a shorter stroke. This is a 4.00-inch stroke crank for an LS engine. Bolt this crank in with a 4.010-bore flat top piston with valve reliefs, a 70cc chamber and a near-zero deck and this will push compression up to over 10.6:1.Photo: Courtesy of Mahle Motorsports
Let’s start with the most basic item of bore size. An aspect that is not generally known is that increasing the bore size will also increase compression. As an example, let’s start with a 6.0L LS engine with a 4.00-inch bore, a 3.62-inch stroke, a 70cc combustion chamber, a pure flat top piston that is 0.005-inch below the deck surface and is using a 0.053-inch-thick head gasket.
Using Summit’s free online compression ratio calculator, the program gives us a compression ratio of 10.1:1. Now, if we increase the bore diameter to 4.030-inch, this increases the static compression ratio to 10.22:1.Then, if we change to a block with a larger 4.155-inch bore, our original 10.1:1 jumps to a more impressive 10.7:1 ratio.
The best way to know the volume of any combustion chamber is to measure it with an affordable 100cc burette and a flat plexiglass plate. This is a simple procedure that produces very accurate results. Photo: Jeff Smith
Stroke has a much more dramatic effect on compression because of the substantial increase in volume that it creates. Let’s take our original 4.00-inch bore and 3.62-inch stroke LS engine stroke at 10.1:1 and add a 4.00-inch stroker crank to the mix. The original displacement was 364ci but now with a longer stroke, the cubic inches expand to a more impressive 402ci. On top of the displacement, this 0.380-inch increase in stroke drastically affects the compression pushing the original 10.1:1 now to 11.06:1.
The inverse is also true where a short stroke engine will have difficulty in creating static compression and is affected by small changes in chamber volume, gasket thickness, and piston top configuration. For this example, we’re going to go way back in time to a small 283ci displacement small-block Chevy to illustrate this point.
The position of the piston relative to the cylinder head deck is also critical. Most engine builders prefer to place the top of the piston at or near the deck surface, but you must also pay careful attention to piston-to-head clearance as well. A tight piston-to-head clearance for a typical wedge cylinder head engine might be 0.037-inch. Photo: Jeff Smith
The stock bore and stroke on a 283 is a combination of a 3.875-inch bore and a 3.00-inch stroke. With a 58cc combustion chamber, a flat top piston with four small (for a total of 8cc) valve reliefs, a 0.020-inch below deck height and a steel shim head gasket that is only 0.015-inch thick, the compression ratio for this engine comes out to 8.96:1. But often hot rodders will bolt a 64cc head on a 283 with bigger valves to try to make more power. What they don’t realize is that with a very short 3.00-inch stroke crank, a small chamber increase in size of 6cc has a big effect on compression. This change to a 64cc head will skewer the original compression ratio of 8.96:1 to 8.35:1 or a loss of over half a ratio!
But changes in chamber volume on a 4-inch stroke engine can be more dramatic even when the percentage of volume change is less than the smaller displacement engine. A change of 6cc in chamber volume on a 4-inch stroke, 4-inch bore engine while keeping all the other variables the same is worth a change of nearly three-quarters of a full point.
Another important variable is the compressed thickness of the head gasket. Many stock LS style MLS head gaskets can measure 0.053-inch and more. If you use one of these gaskets with a piston 0.020-inch below the deck surface, the compression ratio will suffer horribly so it’s always best to check before ordering gaskets.Photo: Jeff Smith
The numbers don’t lie. With a 4.010-inch bore, a 4.00 inch stroke, 70cc chamber, 0.051 gasket, a pure flat top piston, and a piston 0.005-inch below the deck computes out to 11.15:1, but add 6cc with a larger chamber and the compression drops to 10.45:1 or a drop of 0.70:1 in the ratio. These examples offer clues as to how easy it is to generate compression by simple changes.
Even the smallest details can offer advantages if you pay attention to their effects. As an example, piston design is a place where the smart engine builder can take advantage of his choice of piston top configurations. Most engine builders will agree that a small combustion chamber and a flat top piston with small valve reliefs are among the best ways to not only increase compression but also optimize combustion efficiency.
If you are working on an engine with unknown components, you can position the piston a known distance down from the deck and use a 100cc burette to measure the volume of that cylinder. Then compute the volume of a theoretical cylinder with no valve reliefs, dish, or dome. Comparing the theoretical volume with the measured one will produce an accurate description of the piston in question. In this particular case, we established an accurate measurement of the effective dome volume of this piston.Photo: Jeff Smith
The GM LS family of engines is a classic example. Even the original LQ4 6.0 liter LS truck engine from the early 2000’s offered a 7cc dished piston combined with an intermediate sized 71cc combustion chamber to create a 9.5:1 compression ratio to run on 87 octane. A simple trick to enhance power is to add a pair of 5.3L LM4/LM7 heads with smaller 61cc chambers to bump the compression and gain some near free horsepower and torque.
Our calculations reveal a 61cc chamber will push the compression a full point from 9.3:1 to 10.3:1. Even though the 5.3L heads employ smaller intake valves, the increase in compression more than compensates and overall drivability is improved with more torque and horsepower.
Besides the large component options like pistons and combustion chambers, it’s best not to overlook the smaller yet significant details like head gasket thickness and piston deck height. For most engine builders, these two measurements are linked to help establish piston-to-head clearance.
We won’t get into too many details because the options are near limitless. But generally speaking a piston-to-head clearance for a street engine should be established around 0.040-inch or slightly tighter. This is important because sufficient clearance is necessary to prevent piston rock from angling the piston and hitting the combustion chamber.
The modern Gen III hemi head is a hemispherical head in name only. Note that the chamber ends on opposite sides with flat or quench areas. These quench areas help with mixture motion as the piston nears top dead center (TDC) and improves combustion efficiency. Note that all Gen III Hemi engines use two spark plugs per cylinder to compensate for the long distance the flame front would otherwise travel to complete the combustion process. Both plugs fire at the same time and thus help improve both power and fuel mileage. A single spark plug in a Gen III Hemi would require a significantly increased ignition timing to approach the power made by using two plugs per cylinder. Photo: Jeff Smith
For wedge combustion chamber engines, this also establishes a tight quench area which is defined as the area between the flat areas of the chamber and the piston. As the piston arrives at TDC the tight clearance between the head and piston pushes (or squishes) the air and fuel into the chamber. This creates turbulence in the chamber and helps to stir the air and fuel into a more homogenous mixture that will combust more efficiently.
This means if you have an engine like an older small-block Chevy where the piston is buried deep in the cylinder to perhaps 0.025-inch, a thinner head gasket can be used to maintain the piston-to-head clearance at around 0.040-inch or less. One example of this would be the coated thin steel head gasket from Fel-Pro that measures only 0.015-inch (PN 1094) for a 350ci small-block Chevy. This will improve compression compared to a much thicker composition head gasket.
We’ve covered quite a bit of ground regarding compression ratio in hopes of offering some solutions or opportunities that you can take advantage of when building your next engine. It’s often the little details that can make all the difference.
Conversions
There are several free, online compression ratio programs to choose from. This one is from Summit Racing that you can find by searching Summit compression ratio program. These programs allow you to experiment with different chamber, gasket, and piston volumes to come up with the best overall compression ratio for your engine.
Photo: Courtesy of Summit Racing
- To convert cubic inches to cubic centimeters, multiply by 16.3871
- To convert cubic centimeters to cubic inches, multiply by 0.0610
Scaling Back The Squeeze
Some of the hottest muscle cars of the era, like this 427-powered COPO Camaro, had compression ratios of 11:1 or even greater.
Photo: Tommy Lee Byrd
Many muscle car engines from the late 1960s and early 1970s benefitted from compression ratios that were as high as 11:1. With today’s watered-down 91 and occasional 93 octane premium fuel, this often isn’t sufficient to prevent those older engines from detonating. Sure, you can mix in a little octane booster or race gas, but that’s expensive.
With today’s fuel, most sources will suggest no more than 9.0:1 for a compression ratio with iron heads. Our experience indicates you can run closer to 10:1 if the piston-to-head clearance is tight and the heads offer a decent, more modern chamber – like the newer LS engines, for example. Older engines with poor chambers tend to rattle with more than 10:1 to 10.5:1. Camshaft timing also has an effect on performance with bigger cams demanding more static compression compared to a street engine with milder cam timing. These engines are run more favorably with less compression. Of course, the more compression, the more power the engine will make with better efficiency so it’s a critical point.
It’s also possible to slow down the ignition curve and reduce timing, but these tend to make the engine run sluggish and unresponsive, which is not fun to drive. While you could rebuild the engine with a lower compression ratio with different pistons or cylinder heads, there are other alternatives.
Let’s take an example and show how we could reduce the static compression ratio on an original 350-cu.in. LT1 small-block Chevy without changing pistons or using different cylinder heads with larger combustion chambers.
This is a pocket ported 5.3-liter cylinder head from our friends at West Coast Racing Cylinder Heads. Bolting on this smaller 61cc chamber head on a 6.0-liter engine is worth more than one full point in compression. The rule of thumb is one full point of compression is worth roughly 4 percent power, which on a 500 horsepower engine would be worth an additional 20 hp!
Photo: Jeff Smith
We simulated a 1970 LT1 using Summit Racing’s online compression ratio program. We came up with a 4.00-inch bore, 3.48-inch stroke, a 64cc chamber and a piston with a roughly 2cc dome (it’s really bigger but once the valve reliefs are subtracted from the dome volume, the net volume change is roughly 2 cc’s), with the piston 0.025-inch below the deck running a 0.020-inch head gasket. This combination creates a compression ratio of 11.2:1. Often back in those days the compression ratio was often lower than the specs due to production tolerances, but we’ll use these numbers.
One way to reduce compression would be to add a thicker, composition style head gasket. For example, merely replacing the stock shim gasket with a Fel-Pro 0.041-inch composition version will drop the static compression ratio down from 11.2:1 to 10.58:1. This will help but there are repercussions with this approach. This move changes the piston-to-head clearance from roughly 0.045-inch to a much wider 0.066-inch. This reduces the quench effect and might create a situation where this makes the engine more detonation sensitive. This is something to consider before choosing this approach.
A more time-consuming idea would be to increase the combustion chamber volume through grinding the iron chambers. With the addition of 4 cc’s to the chamber volume with the same thin had gasket, it’s possible to cut the compression to 10.64:1. This approach will require some knowledge and skill with a grinder, but it is possible. Of course, using a 68cc aftermarket head will be much better as these more modern heads offer far better chamber designs that can enhance power while often not requiring as much ignition timing.
It’s also possible to add dished intake and exhaust valves that will add one or two cc’s worth of volume with a recessed valve face that might add a slight amount of volume to the chamber. This also reduces the valve weight, which is another positive approach.
These are a few of the better ideas for altering compression for earlier high compression engines. If you have a late ‘70s engine, it will have the exact opposite issue of desperately needing compression with a boost of more than one full point just to get the engine back up somewhere close to 9:1. The best bet with these engines is to just swap to smaller chamber heads. Going from a 76cc chamber to 64cc chamber will pump the compression a full point on a typical 350-cu.in. small-block Chevy.
For car enthusiasts who weren’t around in 1975, you might hear a variation of “look around, what is happening in today’s world is what happened back then.” There is a vein of truth to that. Just a few years ago, buying a car with over 700 horsepower and a warranty that was brightly colored and sounded like the devil’s personal limousine was only a matter of having enough money to cover the purchasing cost. Two-door, four-door, station wagon, sports car, all available. But sooner or later, the party ends and now we have companies trying to foist electric vehicles and small crossovers that they promise will excite in the same way. The sad truth is, they won’t. Something is lost. The “x-factor”.
When the original era of muscle cars ended in the first half of the 1970s, it was the same scene. The only difference was that instead of technologically loaded vehicles, luxury was the by-word. Since you couldn’t feel the grunt of torque like you used to, you might as well feel sumptuous seats, leather-covered surfaces, and a ride that was numb to the road. Surprisingly, this sold well. Chevrolet took inspiration from Pontiac’s Grand Prix for their Monte Carlo and pretty much everyone followed suit. As the pony cars died off one-by-one, they were replaced with a new style: the personal luxury car. Those nameplates that remained evolved into softer, plusher and larger versions of themselves.
The Dodge Charger was no exception. While there were signs of luxury creeping in after the 1971 B-body debuted, the overall shape of the car still meant business, especially on NASCAR circuits where Richard Petty continued his reign as the king. But for 1975, Chrysler Corporation had a problem: they could either chase the Monte Carlo’s path to personal luxury sales, or they could carry over the 1974 body and satisfy enthusiasts but miss the potential sales. Using the new body but designing a unique look for it was out of the question due to Chrysler’s financial issues and the additional manufacturing challenges that would be faced.
A 1977 Chrysler Cordoba, for comparison.Photo: Hemmings Archives
Dodge chose to use the new body that would be shared with the Chrysler Cordoba, and while the Cordoba proved to be a hit right out of the gate, that success didn’t carry over to the Charger. The Cordoba outsold the Charger almost five-to-one between 1975 and 1978, and according to Burton Bouwkamp, the Chrysler Corporation engineer who oversaw the Charger project (among many others), appearance alone was to blame. As he told Allpar in 2004, “In 1974, at a consumer research study to learn how to merchandize the 1975 style, a Charger owner said to me, ‘I see the nameplate on the car, but that is not a Charger!’”
Then there was the insult to injury: Richard Petty never ran the 1975 Charger in NASCAR. It is a documented fact that he loved the 1971-74 Charger body. In his eyes, the shape was perfect for whatever kind of racing he was taking part in. Compared, the 1975 Charger was a barn door that had aerodynamic issues stemming from the rear window being too upright and the decklid being too short. Instead, he utilized the 1974 body until it aged out, at which point he gave the 1978 Dodge Magnum a shot. Let’s just say that Petty didn’t like that car much.
What does one do with a car that doesn’t have racing credentials, that didn’t share the mythical status its nameplate implied, wasn’t as luxurious as its platform mate, and is largely shunned by enthusiasts? The sky is the limit, as this 1975 Dodge Charger Daytona we found on Hemmings Marketplace shows. Painted in two-tone Lucerne Blue Metallic over Silver Cloud Metallic, this Pro Street-inspired Charger features what many don’t see in this era: class, performance, and showmanship. While the Daytona package’s two-tone wasn’t sold exactly like this, eliminating the pinstripe between the colors and moving the “Charger Daytona” callout completely onto the doors cleans up quite a bit of the look. Removing the bumperettes and painting the bumpers and grille surround contributes to the cleaner appearance as well, while the A-body dual-snorkel hood scoop brings a little bit of muscle car flair back.
Under that scoop lies 505 cubic inches of Chrysler RB big-block that has replaced the original 2-barrel 360-cu.in. small-block that originally occupied the engine bay. The modified 727 TorqueFlite sends 657 horsepower and a boatload of torque out to the narrowed 9-inch rear axle with 4.11 gears. Stopping the big B-body is a combination of factory discs up front and Wilwood discs in the rear.
The interior is best described as a custom take on Dodge’s idea of luxury for 1975. The high-back bucket seats, center console, door panels, dash and console all remain, but the faux-woodgrain items have been swapped for aluminum plate, the courtesy lights have custom covers, and the gauges are aftermarket Auto Meter units. There is no ignoring the wheel tubs, the sound system, or the roll cage, but they all continue the blue theme of the interior. Even the trunk, which houses a 20-gallon fuel cell and the battery, is carpeted.
Yes, the Charger crossed over to the dark side in 1975. But there is a silver lining: there is nothing stopping anyone from improving one of these mid-1970s machines. Styling will always be subjective and there is no way anyone could compare it to the 1968-1974 Charger at all. But a comfortable interior, a big-block and a traffic-stopping appearance can make up for a lot of ills.
Trending
