Details, datasheet, quote on part number: FN2969
| Part | FN2969 |
| Category | |
| Description | CMOS Programmable Peripheral Interface |
| Company | Intersil Corporation |
| Datasheet | Download FN2969 Datasheet |
| Quote |
| Features, Applications |
Description The Intersil is a high performance CMOS version of the industry standard 8255A and is manufactured using a self-aligned silicon gate CMOS process (Scaled SAJI IV). is a general purpose programmable I/O device which may be used with many different microprocessors. There are 24 I/O pins which may be individually programmed in 2 groups of 12 and used in 3 major modes of operation. The high performance and industry standard configuration of the 82C55A make it compatible with the 80C86, 80C88 and other microprocessors. Static CMOS circuit design insures low operating power. TTL compatibility over the full military temperature range and bus hold circuitry eliminate the need for pull-up resistors. The Intersil advanced SAJI process results in performance equal to or greater than existing functionally equivalent products at a fraction of the power. FeaturesPin Compatible with NMOS 8255A 24 Programmable I/O Pins Fully TTL Compatible High Speed, No "Wait State" Operation with 5MHz and 8MHz 80C86 and 80C88 Direct Bit Set/Reset Capability Enhanced Control Word Read Capability L7 Process 2.5mA Drive Capability on All I/O Ports Low Standby Power (ICCSB).10�A CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. http://www.intersil.com 407-727-9207 | Copyright � Intersil Corporation 1999 SYMBOL VCC GND D0-D7 RESET WR A0-A1 PIN NUMBER I/O TYPE DESCRIPTION VCC: The +5V power supply pin. A 0.1�F capacitor between pins 26 and 7 is recommended for decoupling. GROUND DATA BUS: The Data Bus lines are bidirectional three-state pins connected to the system data bus. RESET: A high on this input clears the control register and all ports (A, B, C) are set to the input mode with the "Bus Hold" circuitry turned on. CHIP SELECT: Chip select is an active low input used to enable the 82C55A onto the Data Bus for CPU communications. READ: Read is an active low input control signal used by the CPU to read status information or data via the data bus. WRITE: Write is an active low input control signal used by the CPU to load control words and data into the 82C55A. ADDRESS: These input signals, in conjunction with the RD and WR inputs, control the selection of one of the three ports or the control word register. A0 and A1 are normally connected to the least significant bits of the Address Bus A0, A1. PORT A: 8-bit input and output port. Both bus hold high and bus hold low circuitry are present on this port. PORT B: 8-bit input and output port. Bus hold high circuitry is present on this port. PORT C: 8-bit input and output port. Bus hold circuitry is present on this port. BI-DIRECTIONAL DATA BUS D7-D0 DATA BUS BUFFER 8-BIT INTERNAL DATA BUSGROUP A PORT C UPPER (4) GROUP B PORT C LOWER (4) Data Bus Buffer This three-state bi-directional 8-bit buffer is used to interface the 82C55A to the system data bus. Data is transmitted or received by the buffer upon execution of input or output instructions by the CPU. Control words and status information are also transferred through the data bus buffer. Read/Write and Control Logic The function of this block is to manage all of the internal and external transfers of both Data and Control or Status words. It accepts inputs from the CPU Address and Control busses and in turn, issues commands to both of the Control Groups. (CS) Chip Select. A "low" on this input pin enables the communcation between the 82C55A and the CPU. (RD) Read. A "low" on this input pin enables 82C55A to send the data or status information to the CPU on the data bus. In essence, it allows the CPU to "read from" the 82C55A. (WR) Write. A "low" on this input pin enables the CPU to write data or control words into the 82C55A. (A0 and A1) Port Select 0 and Port Select 1. These input signals, in conjunction with the RD and WR inputs, control the selection of one of the three ports or the control word register. They are normally connected to the least significant bits of the address bus (A0 and A1). 82C55A BASIC OPERATION INPUT OPERATION (READ) Port A Data Bus Port B Data Bus Port C Data Bus Control Word Data Bus OUTPUT OPERATION (WRITE) Data Bus Port A Data Bus Port B Data Bus Port C Data Bus Control DISABLE FUNCTION Data Bus Three-State Data Bus Three-State CS POWER SUPPLIES +5V GND GROUP A CONTROL GROUP A PORT A (8) I/O PA7PA0GROUP A PORT C UPPER (4) 8-BIT INTERNAL DATA BUS GROUP B PORT C LOWER (4) FIGURE 1. 82C55A BLOCK DIAGRAM. DATA BUS BUFFER, READ/WRITE, GROUP & B CONTROL LOGIC FUNCTIONS (RESET) Reset. A "high" on this input initializes the control register to 9Bh and all ports (A, B, C) are set to the input mode. "Bus hold" devices internal to the 82C55A will hold the I/O port inputs to a logic "1" state with a maximum hold current of 400�A. Group A and Group B Controls The functional configuration of each port is programmed by the systems software. In essence, the CPU "outputs" a control word to the 82C55A. The control word contains information such as "mode", "bit set", "bit reset", etc., that initializes the functional configuration of the 82C55A. Each of the Control blocks (Group A and Group B) accepts "commands" from the Read/Write Control logic, receives "control words" from the internal data bus and issues the proper commands to its associated ports. Control Group A - Port A and Port C upper - C4) Control Group B - Port B and Port C lower - C0) The control word register can be both written and read as shown in the "Basic Operation" table. Figure 4 shows the control word format for both Read and Write operations. When the control word is read, bit D7 will always be a logic "1", as this implies control word mode information. |
| Some Part number from the same manufacture Intersil Corporation |
| ICL7126CPLZ 3 1/2 Digit, Low Power, Single Chip A/D Converter |
| ISL6299 Li-ion/li-polymer Battery Charger Accepting Two Power Sources |
| X9250TV24I Quad Digitally Controlled Potentiometers |
| UA777M Precision Operational Amplifier |
| EL6196A Laser Diode Driver with Waveform Generator |
| HA5013_04 Triple, 125mhz Video Amplifier |
| HI5710A_00 10-bit, 20 MSPS A/D Converter |
| ISL97644 Boost + LDO + VON Slice + VCOM |
| ISL59110 Triple Channel Video Driver with LPF |
| CD4503 CMOS Hex Buffer |
| U1899 N-channel JFET Switch |
| ISL9011AIRKFZ Dual LDO with Low Noise, Low IQ, and High PSRR |
|
CA5420A : Single 0.5MHz, Low Supply Voltage, Low Input Current Bimos Operational Amplifiers HFA1102IB : 600mhz Current Feedback Amplifier With Compensation Pin HM1-65642883 : 8k X 8 Asynchronous CMOS Static RAM RFD16N02LSM : 16a, 20v, 0.022 Ohm, N-Channel, Logic Level, Power MOSFET ISL89411 : High Speed, Dual Channel Power MOSFET Drivers The ISL89410, ISL89411, ISL89412 ICs are similar to the EL7202, EL7212, EL7222 series but with greater VDD ratings. These are very high speed matched dual drivers capable of delivering peak currents of 2.0A into highly capacitive loads. The high speed p ISL6115A : 12V Power Distribution Controllers This fully featured hot swap power controller targets +12V applications. The ISL6115A with its integrated charge pump has a higher (6.5V vs 5V) gate drive than its sister part the ISL6115 making this part an immediate efficiency improvement replacement. This IC EL5126_06 : 8-channel Tft-lcd Reference Voltage Generator ISL61852EIRZ-T : Dual USB Port Power Supply Controller The ISL6185XXC Is A Family Of 2.5V To 5V Dual Integrated FET Hot Swap Devices Covering The Commercial 0�C To +70�C Temperature Range The ISL6185 USB power controller family provides fully independent overcurrent (OC) fault protection for two or more USB ports. ISL6218CVZ-T : Pmic - Power Management - Specialized Integrated Circuit (ics) Tube 1.4mA 4.75 V ~ 5.25 V; IC CTRLR INTEL PENT M 38-TSSOP Specifications: Applications: Processor ; Current - Supply: 1.4mA ; Voltage - Supply: 4.75 V ~ 5.25 V ; Package / Case: 38-TFSOP (0.173", 4.40mm Width) ; Packaging: Tube ; Operating Temperature: -10�C ~ 85�C ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant X9420YV14Z-2.7T1 : Single Digitally Controlled Potentiometer ISL32432EIUZ : ±40V Fault Protected, 3.3V To 5V, ±15V Common Mode Range, RS-485/RS-422 Transceivers With Cable Invert And ±15kV ESD The ISL32430E through ISL32437E are 3.3V to 5V powered, fault protected, extended common mode range differential transceivers for balanced communication. The RS-485 bus pins (driv EL5373IUZ-T7 : LINE DRIVER Specifications: Device Type: Line / Bus Driver |
| Same catergory |
BY9300Series : Fast High-voltage Soft-recovery Controlled Avalanche Rectifiers. BY9300 series Fast high-voltage soft-recovery controlled avalanche rectifiers Fast high-voltage soft-recovery controlled avalanche rectifiers Plastic package Glass passivated High maximum operating temperature Low leakage current Excellent stability 40% overvoltage allowed during 5 seconds Guaranteed avalanche energy absorption capability Very low reverse. HD29C3487 : Line Drivers. Regarding the change of names mentioned in the document, such as Hitachi Electric and Hitachi XX, to Renesas Technology Corp. The semiconductor operations of Mitsubishi Electric and Hitachi were transferred to Renesas Technology Corporation on April 1st 2003. These operations include microcomputer, logic, analog and discrete devices, and memory chips. IS61LV2568L : 256Kx8. High-speed access time: IS61LV2568LL: 12 ns Operating Current: IS61LV2568L: 50mA (typ.) IS61LV2568LL: 30mA (typ.) Standby Current: IS61LV2568L: 700�A (typ.) IS61LV2568LL: 400�A(typ.) Multiple center power and ground pins for greater noise immunity Easy memory expansion with CE and OE options CE power-down TTL compatible inputs and outputs Single 3.3V. STA723D : Power Transistor , General Purpose Bipolar Power Transistor. General purpose amplifier D-PAK for surface mount applications PC (Collector dissipation)=15W Low speed switching applications Complementary pair with STC722D Collector-Base voltage Collector-Emitter voltage Emitter-Base voltage Collector current Collector dissipation Junction temperature Storage temperature Collector-Base breakdown voltage Collector-Emitter. M5RJ73RPJ : 9x14 mm, 3.3 Volt, Lvpecl/lvds, Clock Oscillator. Integrated phase jitter of less than 1 ps from 12 kHz to 20 MHz Ideal for 10 and 40 Gigabit Ethernet and Optical Carrier applications MtronPTI reserves the right to make changes to the product(s) and service(s) described herein without notice. No liability is assumed as a result of their use or application. Please see www.mtronpti.com for our complete. 22-740 : Short Termination. Full waveguide frequency range Units pressure tested to 30 psi Finish is a unique corrosion-resistant 316 stainless steel epoxy coating Full waveguide frequency range ATM series 720 Terminations utilize a Units pressure tested to 30 psi Precision Conical Element to achieve Finish is a unique corrosion-resistant very low VSWR. 316 stainless steel epoxy. PM-8590 : 10/100 Base-tx Isolation Transformers WITH Filters. � Designed for 10/100MB/s Transmission Over UTP-5 Cable, IEEE 100BASE-TX. � Designed for 350uHY Primary OCL with an 8mA bias. � Designed to Support all leading Fast Ethernet Chip Sets. � Provides the Cable Interface, Isolation & Common Mode Filtering required by the PMD Sublayer. � Through Hole SIP & Low Profile Surface Mount Packages. UL1950, CSA-950. MM74C192J : Synchronous 4-bit Up/down Decade Counter. MM54C192 MM74C192 Synchronous 4-Bit Up Down Decade Counter MM54C193 MM74C193 Synchronous 4-Bit Up Down Binary Counter These up down counters are monolithic complementary MOS (CMOS) integrated circuits The MM54C192 and MM74C192 are BCD counters while the MM54C193 and MM74C193 are binary counters Counting up and counting down is performed by two count. 20017HS : 2.00mm Pitch Connector. BH024E0224KDB : 0.22�F Film Capacitor Radial; CAP FILM 0.22UF 100VDC RADIAL. s: Capacitance: 0.22�F ; Tolerance: �10% ; Dielectric Material: Polyester, Metallized ; Package / Case: Radial ; Packaging: Tape & Reel (TR) ; Lead Spacing: 0.200" (5.08mm) ; ESR (Equivalent Series Resistance): - ; Mounting Type: Through Hole ; : General Purpose ; Lead Free Status: Contains. DFJ-3 : Fuse - Electrical, Specialty Circuit Protection 3kA 600VAC, 450VDC Fast Acting; FUSE 3A 600V FAST CLASS J. s: Current: 3kA ; Voltage - Rated: 600VAC, 450VDC ; Package / Case: Cylindrical ; Fuse Type: Fast Acting ; Mounting Type: Holder ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant. 829264-6 : Gold Through Hole Board To Board - Headers, Receptacles, Female Socket Connectors, Interconnect Receptacle; CONN RCPT 12POS DL VERT .100 GLD. s: Color: Green ; Connector Type: Receptacle ; Contact Finish: Gold ; Contact Finish Thickness: 31.5�in (0.80�m) ; : - ; Height Above Board: 0.244" (6.20mm) ; Height Stacking (Mating): - ; Mounting Type: Through. LDP10IG8-A : Gray, Light PVC Wire Ducts, Raceway Cables, Wire - Management 8.00' (2.44m) Attached Latching Lid; RACEWAY 1CHAN LG AD LGY(8=8'). s: Color: Gray, Light ; : Attached Latching Lid ; Height: 0.860" (21.80mm) ; Length: 8.00' (2.44m) ; Material: PVC ; Mounting Type: Adhesive ; Wire Duct Type: Solid (Raceway), Single Channel ; Width: 1.51" (38.4mm). DAMAM26PNMK52 : Gold Panel Mount D-sub Connectors, Interconnect Plug, Male Pins; DSUB 26 M CRIMP NM G50 HD. s: Connector Type: Plug, Male Pins ; Contact Finish: Gold ; : - ; Flange Feature: Housing/Shell (Unthreaded) ; Mounting Type: Panel Mount ; Number of Positions: 26 ; Number of Rows: 3 ; Termination: Crimp ; Contact Finish Thickness: 50�in (1.27�m) ; Connector. CRCW201051R0FKEF : 51 Ohm 0.75W, 3/4W Chip Resistor - Surface Mount; RES 51.0 OHM 3/4W 1% 2010 SMD. s: Resistance (Ohms): 51 ; Power (Watts): 0.75W, 3/4W ; Tolerance: �1% ; Packaging: Tape & Reel (TR) ; Composition: Thick Film ; Temperature Coefficient: �100ppm/�C ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant. 1608630000 : Terminal Block - Din Rail, Channel Connectors, Interconnect Feed Through; TERM SGL LVL FT 600V 38A WM BLU. s: Color: Blue ; Current - IEC: 41A ; Current - UL: 50A ; : - ; Number of Levels: 1 ; Number of Positions: 2 ; Terminal - Width: 8.1mm ; Termination Style: Push In, Spring ; Type: Feed Through ; Voltage - IEC: 800V ; Voltage - UL: 600V ; Wire Gauge. 935025610602 : F/FAST SERIES, QUAD 2-INPUT NAND GATE, PDSO16. s: Gate Type: NAND ; Supply Voltage: 5V ; Logic Family: TTL ; Inputs: 2 ; Propagation Delay: 5.5 ns ; Operating Temperature: -40 to 85 C (-40 to 185 F) ; Pin Count: 16 ; IC Package Type: Other, 3.90 MM, PLASTIC, SOT-108-1, SO-14. |