FAN8200(D,MTC,MP) by onsemi Datasheet | DigiKey

FAN8200(D,MTC,MP) Datasheet by onsemi

— FAIRCHILD — SEM‘CDNDUCTDR“ 9‘55.
©2004 Fairchild Semiconductor Corporation
www.fairchildsemi.com
Rev. 1.0.5
Features
• 3.3V and 5V MPU interface
• Dual H-bridge drivers for bipolar stepping motor drives
• Built-in vertical-PNP power transistors
• Wide supply voltage range (VCC = 2.5V ~ 7.0V)
• Low saturation voltage (0.4V@ 0.4A)
• Built-in chip enable function for each bridge
• Built-in shoot-through current protection
• Built-in thermal shutdown(TSD) function
Description
The FAN8200/FAN8200D/FAN8200MTC/FAN8200MP is a
monolithic intergrated circuit designed for two-phase step-
ping motor drive systems. It has dual H-bridge drivers with
vertical-PNP power transistors. Each of the bridges has an
independant enable pin, therefore it can be used for other
applications as well as stepping motor drive systems.
Typical Application
• General low voltage stepping motor driver
• Floppy disk driver
• Camera stepping motor driver
• PC camera or security equipment motion controller
• Two channel DC motor driver for a digital still camera
(DSC)
• MPU interfaced general power driver (buffer)
Ordering Information
Device Package Operating Temp.
FAN8200 14-DIP-300 -20 ~ +75°C
FAN8200D 14-SOP-225 -20 ~ +75°C
FAN8200DTF 14-SOP-225 -20 ~ +75°C
FAN8200MTC 14-TSSOP -20 ~ +75°C
FAN8200MTCX 14-TSSOP -20 ~ +75°C
FAN8200MPX 14-MLP -30 ~ +80°C
FAN8200/FAN8200D/FAN8200MTC
FAN8200MP
Low Voltage/Low Saturation Stepping Motor Driver
1
1
14-TSSOP
1
14-DIP-300
14-SOP-225
14-MLP
FAN8200/FAN8200D/FAN8200MTC FAN8200MP
2
Pin Assignments
Pin Definitions
Pin Number Pin Name I/O Pin Function Description
1V
CC - Logic part supply voltage
2 CE1 I Chip enable 1
3 OUT1 O Output 1
4 VS1 - Power supply 1
5 OUT2 O Output 2
6 IN1 I Input 1
7 SGND - Signal ground
8 PGND - Power ground
9 IN2 I Input 2
10 OUT4 O Output 4
11 VS2 - Power supply 2
12 OUT3 O Output 3
13 CE2 I Chip enable 2
14 PGND - Power ground
1234567
1011121314
FAN8200/FAN8200D/
VCC CE1 OUT1 VS1 OUT2 IN1 SGND
PGND CE2 OUT3 VS2 OUT4
98
IN2 PGND
8200MTC/8200MP
% fl J5 #J ‘5 fl
FAN8200/FAN8200D/FAN8200MTC FAN8200MP
3
Internal Block Diagram
1
6
2
7
9
13
14
10
12
11
8
5
3
4
VCC
IN1
CE1
SGND
IN2
CE2
PGND
OUT4
VS2
OUT3
OUT2
PGND
VS1
OUT1
Control
Part2
TSD &
BIAS
Control
Part1
50K
50K
50K
50K
80K
80K
80K
80K
FAN8200/FAN8200D/FAN8200MTC FAN8200MP
4
Absolute Maximum Ratings (Ta = 25°C)
Notes:
1. When mounted on 76.2mm × 114mm × 1.57mm PCB (glass epoxy material).
2. Power dissipation reduces 8.0mW/°C for FAN8200, 4.8mW/°C for FAN8200D, 6.9mW/°C for FAN8200MTC and 6.4mW/°C
FAN8200MP for Ta ≥ 25°C.
3. Should not exceed PD and SOA(Safe Operating Area).
Power Dissipation Curve
Parameter Symbol Value Unit
Supply voltage VCC(MAX) 9.0 V
Power supply voltage VS(MAX) 9.0 V
Output voltage VOUT(MAX) VS + VCF V
Input voltage VIN(MAX) 7.0 V
Peak output current per channel IO(PEAK) 1A
Continuous output current per channel IO
0.65 (FAN8200)
0.4 (FAN8200D)
0.55 (FAN8200MTC)
0.35 (FAN8200MP)
A
Power dissipation PDnote
1.0 (FAN8200)
0.6 (FAN8200D)
0.87 (FAN8200MTC)
0.8 (FAN8200MP)
W
Junction temperture TJ150 °C
Storage temperature TSTG -40 ~ 125 °C
Operating temperature TA
-20 ~ 75(FAN8200)
-20 ~ 75(FAN8200D)
-20 ~ 75(FAN8200MTC)
-30 ~ 80(FAN8200MP)
°C
00 25 50 75 100 125
Ambient temperature, Ta [°C]
150 175
0.5
1.0
Power
Dissipation
: PD[W]
FAN8200
SOA
00255075100125
Ambient temperature, Ta [°C]
150 175
0.6
1.0
Power
Dissipation
: PD[W]
FAN8200D
SOA
FAN8200/FAN8200D/FAN8200MTC FAN8200MP
5
Power Dissipation Curve (Continued)
Recommended Operating Conditions (Ta = 25°C)
Parameter Symbol Min. Typ. Max Unit
Logic circuit supply voltage VCC 2.5 - 7.0 V
Power supply voltage VS2.5 - 7.0 V
00 25 50 75 100 125
Ambient temperature, Ta [°C]
150 175
0.5
1.0
Power
Dissipation
: PD[W]
FAN8200MTC
SOA
00255075100125
Ambient temperature, Ta [°C]
150 175
0.5
1.0
Power
Dissipation
: PD[W]
FAN8200MP
SOA
FAN8200/FAN8200D/FAN8200MTC FAN8200MP
6
Function Descriptions
X: don’t care
Z: high-impedance
CE1 IN1 OUT1 OUT2 CE2 IN2 OUT3 OUT4
Low X Z Z Low X Z Z
High Low High Low High Low High Low
High High Low High High High Low High
CE1
CE2
IN1
IN2
Phase-A
OUT1-OUT2
Phase-B
OUT3-OUT4
+VS
-VS
+VS
-VS
High-ImpedanceHigh-Impedance
FAN8200/FAN8200D/FAN8200MTC FAN8200MP
7
Electrical Characteristics
(Ta=25°C, VCC=5V, VS1=3V, VS2=3V, unless otherwise specified)
Typical Performance Characteristics
VSAT vs. IOUT Characteristics Graph
Parameter Symbol Conditions Min. Typ. Max. Unit
Supply current 1 ICC1 CE1, 2=0V - 0.1 10 uA
Supply current 2 ICC2 CE1=3V, CE2=0V
or CE1=0V, CE2=3V -1218mA
Saturation voltage 1
(upper + lower total) VSAT1 CE1=3V, IN1=3V
or 0V, IOUT=0.2A -0.20.3V
Saturation voltage 2
(upper + lower total) VSAT2 CE1=3V, IN1=3V
or 0V, IOUT=0.4A -0.40.6V
Input high level voltage VINH -1.8-V
CC V
Input low level voltage VINL --0.3-0.7V
Input current IIN IN=3V, Each pin - 100 200 uA
Chip enable current ICE CE=3V, Each pin - 100 200 uA
Clamp diode leakge current ILEAK VCC=7V, VS=7V - - 30 uA
Clamp diode voltage VCF IOUT=0.4A - - 1.7 V
0 100 200 300 400 500 600 70
0
0
0.4
0.8
1.0
0.2
0.6
V
SAT
[V]
IO[A]
0 100 200 300 400 500 600 70
0
0
0.4
0.8
1.0
0.2
0.6
V
SAT
[V]
IO[A]
VSAT[V]
IOUT[A]
L; kwfl LTm
FAN8200/FAN8200D/FAN8200MTC FAN8200MP
8
Test Circuits
1
6
2
7
9
13
14
10
12
11
8
5
3
4
VCC
IN1
CE1
SGND
IN2
CE2
PGND
OUT4
VS2
OUT3
OUT2
PGND
VS1
OUT1
Control
Part2
TSD &
BIAS
Control
Part1
VCC 0.1uF
SW1
SW2
SW4
SW5
15Ω6Ω
SW6
SW7
15Ω
6Ω
SW3
LTm
FAN8200/FAN8200D/FAN8200MTC FAN8200MP
9
Typical Application Circuit
1
6
2
7
9
13
14
10
12
11
8
5
3
4
VCC
IN1
CE1
SGND
IN2
CE2
PGND
OUT4
VS2
OUT3
OUT2
PGND
VS1
OUT1
Control
Part2
TSD &
BIAS
Control
Part1
VCC 0.1uF
From
Motor
Stepping
Microprocessor
3.3V or 5V
me 3 3v m 5v Mmmpmcassnr P» IAsI: A 3* PHASE a :‘F ENABLE L, 3.3V(or 5V) 11 mi Twp A1 0 From 3 3v or 5v chropmoessm / 5v 5v STEPP‘NG MOTOR 3 Gun 5 0sz a VA 2 Gus 7 72 0 Gun J v2
FAN8200/FAN8200D/FAN8200MTC FAN8200MP
10
Application Example - Full Step Bipolar Drive
Circuit Schematics
Application Example - Large Current Buffer
Circuit Schematics
FAN8200/D/MTC
FAN8200/D/MTC
3.3V(or 5V) 3,3V(or 5V) Dmr >1uF EU From 3 3v or 5v Mmroprucessur
FAN8200/FAN8200D/FAN8200MTC FAN8200MP
11
Application Example - 2-Ch. dc Motor Driver for a Digital Still Camera(DSC)
Circuit Schematics
M
Shutter
dc motor
M
Iris
dc motor
IN1=high IN1=low
IN2=high IN2=low
Shutter
direction
Shutter
enable
Iris
direction
Iris
enable
FAN8200/D/MTC
FAN8200/FAN8200D/FAN8200MTC FAN8200MP
12
Mechanical Dimensions (Unit: mm)
Package Dimensions
6.40 ±0.20
7.62
0.300
2.54
0.100
#
1
#
7#8
#14
0.252 ±0.008
0~15°
0.25 +0.10
–0.05
0.010 +0.004
–0.002
3.30 ±0.30
0.130 ±0.012
3.25 ±0.20
0.128 ±0.008
19.40 ±0.20
0.764 ±0.008
19.80
0.780 MAX
5.08
0.200
0.20
0.008
MAX
MIN
2.08
0.082
(
)
0.46 ±0.10
0.018 ±0.004
0.059 ±0.004
1.50 ±0.10
14-DIP-300
FAN8200/FAN8200D/FAN8200MTC FAN8200MP
13
Mechanical Dimensions (Unit: mm) (Continued)
Package Dimensions
8.56 ±0.20
0.337 ±0.008
1.27
0.050
5.72
0.225
1.55 ±0.10
0.061 ±0.004
0.05
0.00
2
6.00 ±0.30
0.236 ±0.012
3.95 ±0.20
0.156 ±0.008
0.60 ±0.20
0.024 ±0.008
8.70
0.343 MAX
#1
#7 #8
0~8°
#14
0.47
0.019
()
1.80
0.071
MAX0.10
MAX0.004
MAX
MIN
+0.10
-0.05
0.20
+0.004
-0.002
0.008
+0.10
-0.05
0.406
+0.004
-0.002
0.016
14-SOP-225
Emu 510[ 201) 4 no( 193) 4 scum 4‘30(.|69) ‘HHHFH' | —-——__._ _, El PIN #1 INDEX SEA'HNG PLANE MIN. MIN. macaw) R a.us(.aa¢) a El .IHEJHEJHH a 554,255) 615$“) a.55[.uzs)asc —i 1,2n(,047)mx —D jLfig‘flfi) il-EEIIM mamas» M1— . 0-25(.DI°) _/ fl 0' — 5' Y 0.152.005) 0.751.030) 0—.os(.uuz) D so( 020)
FAN8200/FAN8200D/FAN8200MTC FAN8200MP
14
Mechanical Dimensions (Unit: mm) (Continued)
Package dimensions
14-TSSOP
van Bum NE #98 E N'DWDLO J m u N? u o w r c c c c C L c m 5 0 U H a. w m. m o 2. m a. n 1 \l U ,I. _ 1 fl 3 3 n 3 a S i S o m m nhmwonm Pm mmn 953.8 4 n M x a 7 a. n a ¢ DIDIDIDIDIDID
FAN8200/FAN8200D/FAN8200MTC FAN8200MP
15
Mechanical Dimensions (Unit: mm) (Continued)
Package dimensions
14-MLP
FAN8200/FAN8200D/FAN8200MTC FAN8200MP
9/13/04 0.0m 001
Stock#DSxxxxxxxx
2003 Fairchild Semiconductor Corporation
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES
OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body,
or (b) support or sustain life, and (c) whose failure to
perform when properly used in accordance with
instructions for use provided in the labeling, can be
reasonably expected to result in a significant injury of the
user.
2. A critical component in any component of a life support
device or system whose failure to perform can be
reasonably expected to cause the failure of the life support
device or system, or to affect its safety or effectiveness.
www.fairchildsemi.com
DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY
PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY
LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER
DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.