The HFDOM44S6Vxxx series 44Pin Flash Disk Module is a flash technology based with True IDE interface flash memory card. It is constructed with flash disk controller chip and NAND-type (Samsung) flash memory device. The HFDOM44S6V-xxx series operates in both 3.3-Volt and 5.0-Volt power supplies. It comes in capacity to 3GByte formatted 44Pin type. By optimizing flash memory management, the life of this HFDOM44S6Vxxx series can be extended to its maximum level. Because the ECC function is included, the correctness of data transfer between the HFDOM44S6Vxxx series and a True IDE compatible interface device can be guaranteed. The HFDOM44S6Vxxx series is fully compatible with applications such as CPU card / board, set top box, industry / military PC / Notebook, security equipment, measuring instrument and embedded systems.

ATA / True IDE compatible host interface ATA command set compatible Automatic sensing of PC Card ATA or true IDE host interface. Very high performance, very low power consumption Automatic error correction Auto Standby to save power consumption. Supports power down commands and sleep modes. Integrated PCMCIA attribute memory of 256 bytes (CIS) Support for or 16 bit host transfers 3.3V/5.0V operation voltage Host Interface bus width : 8/16 bit Access Flash Interface bus width : 8 bit Access Capacity : Min. 128MB ~ Max. 3GB MTBF > 1,000,000 hours. Minimum 10,000 insertions. Shock 2,000 G max. Vibration 15 G peak to peak max.

Symbol VDD VIN VOUT TSTG Parameter Power supply Input voltage Output voltage Storage temperature Rating to VDD+0.3 Units

Sym. VIL VIH VIL VIH VOL VOH RI Parameter Input low voltage Input high voltage Schmitt input low voltage Schmitt input high voltage Output low voltage Output high voltage Input pull up/down resistance Min V k Typ Max 0.3VDD Units

Plug the carefully into the 44pin IDE slot on your computer. Caution: Make sure to align pin1 on host adapter interface connector with pin 1 on your Flash Disk Module. Pin 1 is indicated by a triangle on the Flash Disk Module connector. The Flash Disk Module is used power connector cable of the computer. Caution: If you need to remove your Flash Disk Module, use both hands to pull it out carefully. Check all cable connections and then replace your computer cover.

Before you format or partition your new drive, you must configure your computer's BIOS so that the computer can recognize your new drive. Turn your computer on. As your computer start up, watch the screen for a message describing how to run the system setup program on the screen (sometimes called BIOS or CMOS setup). This is usually done by pressing a special key, such as Delete, Esc or F1 during startup. See your computer manual for details. Press the appropriate key to run the system setup program. If your BIOS provides automatic drive detection (an "AUTO" drive type), select this option. ( We recommend to use Normal / CHS mode to partition your Flash Disk Module to get the maximum formatted capacity. ) This allows your computer to configure itself automatically for your new drive. If your BIOS dose not provide "AUTO" drive detection, select "User-defined" drive setting and enter the CHS values from the table. BIOS Settings (see specification) Capacity Cylinders Heads Sectors(unformatted) Save the settings and exit the System Setup program. ( your computer will automatically reboot ) After you configure your computer, you can use the standard DOS commands to partition and format your Flash Disk Module, as described below.

To partition your new Flash Disk Module with Microsoft DOS program : Insert a bootable DOS diskette into your diskette drive and restart your computer. Insert a DOS program diskette that contains the FDISK.EXE and FORMAT.COM programs into your diskette drive. Use the same DOS version that is on your bootable diskette. At the A:\ > prompt, type "FDISK" and press Enter. Select "Create DOS partition or logical DOS drive" by pressing 1. Then press Enter. Select "Create primary DOS partition" by pressing 1 again. Then press Enter. Create your first drive partition. If you are creating a partition that will be used to boot your computer (drive C), make sure that the partition is marked active. Create an extended partition and additional logical drives as necessary, until all the space on your new hard drive has been partitioned. When the partitioning is complete, FDISK reboots your computer. Caution: Make sure to use the correct drive letters so that you do not format a drive that already contains data. At the A:\ > prompt, type "format c:/s", where c is the letter of your first new partition, Repeat the format process for all the new partitions you have created. After you format your drive, it is ready to use.