Below is a snapshot of the Web page as it appeared on 3/29/2024 (the last time our crawler visited it). This is the version of the page that was used for ranking your search results. The page may have changed since we last cached it. To see what might have changed (without the highlights), go to the current page.
Bing is not responsible for the content of this page.
BK PRECISION 4007DDS INSTRUCTION MANUAL Pdf Download | ManualsLib
9830 series
high power programmable ac power
source (93 pages)
Summary of Contents for BK Precision 4007DDS
Page 1
Model 4007DDS 7 MHz Sweep Function Generator...
Page 2
Model 4007DDS - Instruction Manual Limited Two-Year Warranty B&K Precision warrants to the original purchaser that its products and the component parts thereof, will be free from defects in workmanship and materials for a period of two years from date of purchase from an authorized B&K Precision distributor.
Page 3
Contents Section 1 Introduction DESCRIPTION ......................SPECIFICATIONS ....................TECHNICAL SUPPORT ................... Section 2 Installation INTRODUCTION...................... INSTRUMENT MOUNTING ................... POWER REQUIREMENTS ..................GROUNDING REQUIREMENTS ................SIGNAL CONNECTIONS ..................ACCEPTANCE CHECK ................... Section 3 Operating Instructions CONTROLS AND CONNECTORS................INSTRUMENT INPUTS AND OUTPUTS ............... FIRST TIME OPERATION..................
Page 4
Model 4007DDS - Instruction Manual Safety Summary The following safety precautions apply to both operating and maintenance personnel and must be observed during all phases of operation, service, and repair of this instrument. Before applying power, follow the installation instructions and become familiar with the operating instructions for this instrument.
Page 5
Introduction 1.1 SCOPE This manual contains installation instructions, test procedures, operation procedures and troubleshooting information required to operate, test and maintain the Model 4007DDS Function Generator. 1.2 DESCRIPTION The Model 4007DDS is a versatile, high performance function generator. Implemented using advance digital technologies based on DDS topology, the unit generates superb quality waveforms with high precision and stability.
Page 6
Model 4007DDS - Instruction Manual AMPLITUDE FLATNESS ..........±1 dB to 7 MHz. OFFSET RANGE ............Variable up to ±10V (±5V into 50Ω). Absolute peak amplitude plus offset limited to ±10V (±5V into 50Ω). OUTPUT IMPEDANCE ..........50Ω OUTPUT PROTECTION ..........The generator main output is non-destructively protected against short circuit to ground or to any voltage practically available in electronic laboratories.
Page 7
“FRAGILE”. 2.3 INSTRUMENT MOUNTING The Model 4007DDS is intended for bench use. The unit can be installed in a closed rack or test stand if proper airflow is assured for removing about 15W of power dissipation. The instrument does not require special cooling when operated within conventional temperature limits. The instrument includes a front feet tilt mechanism for optimum panel viewing angle.
Page 8
Model 4007DDS - Instruction Manual 2.6 SIGNAL CONNECTIONS Use RG 58 coaxial cables for all input and output signals to and from the unit. 2.7 ACCEPTANCE CHECK This acceptance check is a general verification of generator operation. Set the power on and allow a 15-minute warm-up period.
Page 9
Section 3 Operating Instructions 3.1 CONTROLS AND CONNECTORS Front panel controls and connectors are shown in the front view illustration of the Model 4007. Each operating control is described as follows: POWER ON/OFF – Applies or removes AC power to the unit. FREQUENCY –...
Page 10
Model 4007DDS - Instruction Manual 3.2 INSTRUMENT INPUTS AND OUTPUTS The Model 4007 main output impedance is 50Ω. The output can deliver up to 10V peak-to-peak waveforms into a 50Ω load. Proper signal loading and connection is necessary for the generator main output to meet its specifications.
Page 11
3.5 DETAILED OPERATING INSTRUCTIONS 3.5.1 Frequency Setting The frequency of the generator is changed by turning the FREQUENCY control. The frequency range is selected by pressing the up or down range pushbuttons. The waveform output frequency is shown on the LCD display. 3.5.2 Variable Symmetry The symmetry of the Square waveform can be changed by pushing the DUTY CYCLE ON button and rotating the DUTY CYCLE knob.
Page 12
Model 4007DDS - Instruction Manual V092612...