The a 5V differential receiver that contains an internally supply voltage source, VBB. When used in a single ended input condition the unused input must be tied to VBB. When operating in this mode use 0.01 �F capacitor to decouple VBB and VCC and also limit the current sinking or sourcing capability to 0.5mA. When VBB is not used it should be left open. With inputs open or both inputs at VEE the differential Q output defaults LOW. The 100 series is temperature compensated.

s Typical propagation delay ps s Typical IEE mA s Internal pull-down resistors on inputs s Fairchild MSOP-8 package is a drop-in replacement TSSOP-8 s Meets or exceeds JEDEC specification EIA/JESD78 IC latch-up test s Moisture Sensitivity Level 1 s ESD Performance: Human Body Model > 2000V Machine Model > 200V

Package Order Number 100EL16M 100EL16M8 (Preliminary) Number M08A MA08D Product Code Top Mark KL16 8-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150" Narrow 8-Lead Molded Small Outline Package (MSOP), JEDEC MO-187, 3.0mm Wide Package Description

Devices also available in Tape and Reel. Specify by appending suffix letter "X" to the ordering code.

Pin Name D, D VBB VCC VEE NC Description ECL Data Outputs ECL Data Inputs Reference Voltage Positive Supply Negative Supply No Connect

PECL Supply Voltage (VCC) VEE = 0V NECL Supply Voltage (VEE) VCC = 0V PECL DC Input Voltage (VI) VEE = 0V NECL DC Input Voltage (VI) VCC 0V DC Output Current (IOUT) Continuous Surge VBB Sink/Source Current (IBB) Storage Temperature (TSTG) to +8.0V

PECL Power Supply (VEE = 0V) NECL Power Supply (VCC = 0V) Free Air Operating Temperature (TA) VEE to -5.5V VCC to 5.5V

Note 1: The "Absolute Maximum Ratings" are those values beyond which the safety of the device cannot be guaranteed. The device should not be operated at these limits. The parametric values defined in the Electrical Characteristics tables are not guaranteed at the absolute maximum rating. The "Recommended Operating Conditions" table will define the conditions for actual device operation.

Symbol IEE VOH VOL VIH VIL VBB VIHCMR IIH IIL Parameter Power Supply Current Output HIGH Voltage (Note 3) Output LOW Voltage (Note 3) Input HIGH Voltage (Single Ended) Input LOW Voltage (Single Ended) Output Voltage Reference Input HIGH Voltage Common Mode Range (Differential) (Note 4) Input HIGH Current (Note 5) Input LOW Current (Note -40�C Min Typ 3995 3305 Max Min 25�C Typ 4045 3295 Max Min 85�C Typ 4050 3295 Max Units V �A

Note 2: Input and output parameters vary to 1 with VCC. VEE can vary +0.8V/-0.5V. Note 3: Outputs are terminated through a 50 Resistor to VCC - 2.0V. Note 4: VIHCMR minimum varies to 1 with VEE. VIHCMR maximum varies 1-to-1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPMIN and 1V. Note 5: Absolute value of the input HIGH and LOW current should not exceed the absolute value of the stated Min or Max specification. Note: Devices are designed to meet the DC specifications after thermal equilibrium has been established. Circuit is tested with air flow greater than 500LFPM maintained.

Symbol IEE VOH VOL VIH VIL VBB VIHCMR IIH IIL Parameter Power Supply Current Output HIGH Voltage (Note 7) Output LOW Voltage (Note 7) Input HIGH Voltage (Single Ended) Input LOW Voltage (Single Ended) Output Voltage Reference Input HIGH Voltage Common Mode Range (Differential) (Note 8) Input HIGH Current (Note 9) Input LOW Current (Note -40�C Min Typ -1005 -1695 Max Min 25�C Typ -955 -1705 Max Min 85�C Typ -955 -1705 Max Units V �A

Note 6: Input and output parameters vary to 1 with VCC. VEE can vary +0.8V/-0.5V. Note 7: Outputs are terminated through a 50 Resistor to VCC - 2.0V. Note 8: VIHCMR minimum varies to 1 with VEE. VIHCMR maximum varies to 1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPMIN and 1V. Note 9: Absolute value of the input HIGH and LOW current should not exceed the absolute value of the stated Min or Max specification.

Note: Devices are designed to meet the DC specifications after thermal equilibrium has been established. Circuit is tested with air flow greater than 500LFPM maintained.

Symbol fMAX Parameter Maximum Toggle Frequency 125 75 (SE) tSKEW tJITTER VPP tr, tf Duty Cycle Skew (Note 12) Cycle-to-Cycle Jitter Input Swing Output Rise Times to -40�C Min Typ TBD 250 5 TBD Max Min 25�C Typ TBD 250 5 TBD Max Min 85�C Typ TBD 280 5 TBD Max Units GHz mV ps Figure 1 Figure 2 Figures 1, 3 Figure Number

Note 10: VEE can vary / -0.5V. Note 11: Measured using 750 mV input swing centered at VCC 1.32V; 50% duty cycle clock source; 80%) at fIN = 1 MHz. All loading with 50 to VCC - 2.0V. Note 12: Duty cycle skew is the difference between a tPLH and tPHL propagation delay through a device under identical conditions.