Below is a snapshot of the Web page as it appeared on 4/5/2024 (the last time our crawler visited it). This is the version of the page that was used for ranking your search results. The page may have changed since we last cached it. To see what might have changed (without the highlights), go to the current page.
Bing is not responsible for the content of this page.
BTS620L1 - Smart Two Channel Highside Power Switch
PROFET® BTS 620 L1
Smart Two Channel Highside Power Switch
Features
• Overload protection • Current limitation • Short circuit protection • Thermal shutdown • Overvoltage protection (including load dump) • Reverse battery protection1) • Undervoltage and overvoltage shutdown with auto-restart and hysteresis • Open drain diagnostic output • Open loa More View
d detection in ON-state • CMOS compatible input • Loss of ground and loss of Vbb protection • Electrostatic discharge (ESD) protection
Product Summary Overvoltage protection Operating voltage
Vbb(AZ) Vbb(on)
43 5.0 ... 24
both
V V
channels: On-state resistance RON Load current (ISO) IL(ISO) Current limitation IL(SCr)
each parallel 100 50 mΩ 4.4 8.5 A 10 10 A
TO-220AB/7
Application
• µC compatible power switch with diagnostic feedback for 12 V DC grounded loads • Most suitable for resistive and lamp loads
7 1
Standard
General Description
N channel vertical power FET with charge pump, ground referenced CMOS compatible input and diagnostic feedback, monolithically integrated in Smart SIPMOS® technology. Fully protected by embedded protection functions.
Voltage source
Overvoltage protection
Current limit 1
Gate 1 protection
+ V bb
4
V
Logic
Voltage sensor
Level shifter Rectifier 1 Charge pump 1 Charge pump 2 Open load Short to Vbb detection 1 Current limit 2 Gate 2 protection Temperature sensor 1
OUT1
1
3 6 5
IN1 IN2
ESD
ST
Logic
Level shifter Rectifier 2
OUT2
Temperature sensor 2 Open load Short to Vbb detection 2
R O1 GND R O2
7
Load
® PROFET 2
GND Signal GND
Load GND
1)
With external current limit (e.g. resistor RGND=150 Ω) in GND connection, resistor in series with ST connection, reverse load current limited by connected load.
Semiconductor Group
1
12.96
BTS 620 L1
Pin 1 2 3 4 5 6 7 Symbol OUT1 (Load, L) GND IN1 Vbb ST IN2 OUT2 (Load, L) Function Output 1, protected high-side power output of channel 1 Logic ground Input 1, activates channel 1 in case of logical high signal Positive power supply voltage, the tab is shorted to this pin Diagnostic feedback: open drain, low on failure Input 2, activates channel 2 in case of logical high signal Output 2, protected high-side power output of channel 2
Maximum Ratings at Tj = 25 °C unless otherwise specified Parameter Supply voltage (overvoltage protection see page 3) Supply voltage for full short circuit protection Tj Start=-40 ...+150°C Load dump protection2) VLoadDump = UA + Vs, UA = 13.5 V RI3)= 2 Ω, RL= 2.7 Ω, td= 200 ms, IN= low or high Load current (Short circuit current, see page 4) Operating temperature range Storage temperature range Power dissipation (DC), TC ≤ 25 °C Electrostatic discharge capability (ESD) IN: (Human Body Model) all other pins:
acc. MIL-STD883D, method 3015.7 and ESD assn. std. S5.1-1993
Symbol Vbb Vbb
Values 43 24 60 self-limited -40 ...+15
Similar Datasheet
BTS6201U Wideband high linearity pre-driver amplifier - NXP
BTS620L1 Smart Two Channel Highside Power Switch - Siemens Semiconductor Group